How To Install Pop Up Drain In Yard

Drain emitters that pop out around the perimeter of your home are a simple remedy for drainage issues. When it’s not feasible to build a drainage system that allows water to sink into the ground, a pop-up drain system allows you to divert it to a point where it can safely run downhill or out to the street.

When there is water to drain, a pop-up drain opens and closes when the ground is dry, successfully keeping trash and small animals out of the system. What is a pop-up drain, exactly? It’s a drainage system that moves water away from a house’s foundation more effectively than a regular downspout.

Benefits Of Pop Up Drain Installation In The Yard:

Pop-up emitter drains have the advantage of closing when not in use, thereby preventing small animals and garbage from entering your drains. The drains do not require any power to work due to hydrostatic pressure. The following procedures generally apply, although specific installation instructions will differ based on your situation.

The advantage of pop-up emitters is that the lid stays shut if there isn’t a steady water flow. This implies that no debris can enter the pipe. It’s an excellent alternative to standard drain grates, which tend to gather rocks, dirt, and leaves, clogging the line over time.

Steps To Install The Pop Up Drain In The Yard:

Consider installing a pop-up emitter if you need to increase your downspout drainage. Even the most beginner do-it-yourself will be able to do this inexpensive DIY project in less than an afternoon.

1)Determine The Distance:

Calculate the distance between the runoff source and the water-safe drainage region. Ascertain that the slope is enough to direct the emitter’s flow to a safe location. The top of the emitter must be at a lower elevation than the pipe inlet for optimal performance.

2)Collect The Required Material:

Purchase enough drainage pipe based on your measurements, then choose the best pop-up emitter for the job. Pop-up drains come in various brands and sizes, and the box instructions will help you choose.

3)Install A Catch Basin:

Installing a catch basin to restrict water flow away from a roof gutter downspout is advised. Excavate a trench large enough to accommodate the catch basin. Water should be piped from the catch basin to a pre-determined discharge point, which should be at least 10 feet away from the building.

4)Dig A Trench:

This is the most time-consuming component of the project, but it’s smooth sailing after that. Dig a ditch at least several feet away from your house and deep enough to accommodate the drainpipe properly. Dig the hole deep enough for the pipe to be laid at the proper angle for proper flow. Remember that the emitter’s top should be lower than the pipe inlet.

5)Install The Drainage Pipes:

The manufacturer’s instructions will always take precedence, but there are few variables to worry about since these drains work on hydrostatic pressure. Connect the pipe’s input end to your water drainage area’s source of water. PVC cement should be used to assemble the pipe. Backfill the trench after installing a PVC elbow at the emitter’s placement and gluing the emitter to the elbow, so it rests at ground level.

6)Cover The Drainage Pipe:

Cover the area around your new pipe with earth and grass seed. Your new drains will be virtually inconspicuous except when they are in use in no time. Even though your pop-up emitter drains are generally low-maintenance, it’s a good idea to check them now and then to make sure they’re not blocked. Make sure they’re recessed when you mow your lawn, rake your leaves, or conduct other common yard chores.

7)What Are The Benefits Of Landscape Gravel For The Pop Up Drain?

Gravel can bring your plants to life. Landscaping gravel also helps keep water away from the roots by providing drainage. Gravel and stone are simple to install and maintain. Simply lay down a weed block or plastic covering first to prevent weed growth.

The term sunshine out refers to the continuance of this specified grade or slope until no more earth remains and the pipe exits into the daylight. The engineer specifies that the plumbing should continue to run until there is no more cover or material over the pipe, allowing daylight to pass through.

8)When The Drain Pipe Gets Mute?

The top is designed to pop up and disperse the water over the ground when it rains. They also have a bottom weep hole to drain any water that isn’t being pushed out by the downspouts. However, if it’s below freezing outside, the water in the downspout should be below freezing as well, making this assertion meaningless.

Dig a trench 6-inches wider than the drain pipe you wish to bury and 3 inches deeper than the drain pipe. If there is enough room, Weisman suggests extending the trench at least 8-feet from the downspout.

Conclusion:

Water can be diverted and discharged to water-safe locations away from structures, erosion-prone landscapes, and areas with poor drainage using a pop-up drainage emitter. The hydrostatic pressure of water flowing through the drain pipe causes the pop-up drainage emitter to open; as the flow decreases, the emitter closes.

You won’t even detect the emitter in your yard once it’s placed and the grass has grown back. Even if it’s out of sight and out of mind, it’s still necessary to check on it regularly. To keep the emitter functioning well, make sure any blockages are removed.

Total
0
Shares
Related Posts